Publications
2008
1. Haapala, K. R., J. L. Rivera, and J. W. Sutherland, "Application of Life Cycle Assessment Methods to Sustainable Product Design and Manufacturing," International Journal of Innovative Computing, Information and Control, Special Issue on Recent Advances in Flexible Automation, Vol. 4, No. 3, 2008, pp. 575-589. [PDF]
2. Haapala, K. R., K. L. Brown, and J. W. Sutherland, "A Life Cycle Environmental and Economic Comparison of Product-Service Systems," Trans. of NAMRI/SME, Vol. 36, pp. 333-340, 2008. [PDF]
3. Sutherland, J. W., D. P. Adler, K. R. Haapala, and V. Kumar, "A Comparison of Manufacturing and Remanufacturing Energy Intensities with Application to Diesel Engine Production," CIRP Annals, Vol. 57, No. 1, 2008, pp. 5-8. [PDF]
4. Kumar, V. and J. W. Sutherland, "Sustainability of the Automotive Recycling Infrastructure: Review of Current Research and Identification of Future Challenges," International Journal of Sustainable Manufacturing, Vol. 1, Nos. 1/2, 2008, pp. 145-167. [PDF]
5. Hutchins, M. J. and J. W. Sutherland, "An Exploration of Measures of Social Sustainability and Their Application to Supply Chain Decisions," Journal of Cleaner Production, Vol. 16, 2008, pp. 1688-1698. [PDF]
6. Ju, C., J. Sun, D. J. Michalek, and J. W. Sutherland, "Development of an Imaging System and its Application in the Study of Cutting Fluid Atomization in a Turning Process," Particulate Science and Technology Journal, Vol. 26, No. 4, 2008, pp. 318-336. [PDF]
7. Jenkins, T. L. and J. W. Sutherland, "An Integrated Supply System for Forest Biomass," Chapter 5 in Renewable Energy From Forest Resources in the United States, Ed.: B. D. Solomon and V. A. Luzadis, Routledge, Oxfordshire, UK, November 2008, pp. 92-115. [PDF]
8. Clarke, A., Q. Zhang, J. Gershenson, and J. Sutherland, "Selection of Remanufacturing Facility Locations to Minimize Cost and Environmental Impact," Proceedings of 15th CIRP International Conference on Life Cycle Engineering, Sydney, Australia, March 2008, appeared on CD-ROM. [PDF]
9. Johnson, D. M., G. A. Graman, L. J. Bohmann, K. Mattila, N. Onder, and J. W. Sutherland, "Service Systems Engineering: New Course Development – Service Systems Operations," Proceedings of 2008 POMS Conference, La Jolla, California, May 2008. [PDF]
10.
Sutherland, J. W., J. L. Rivera, K. L. Brown, M. Law, M. J. Hutchins, T. L. Jenkins,
and K. R. Haapala, "Challenges for the Manufacturing Enterprise to Achieve
Sustainable Development," Proceedings of the 41st CIRP
Conference on Manufacturing Systems,
11. Rickli, J. L., A. R. Clarke, K. R. Haapala, M. Addo, J. A. Camelio, and J. W. Sutherland, “Reducing the Environmental and Social Impacts of E-Waste Recovery in Developing Countries Through Technology and Policy,” Global Conference on Sustainable Product Development and Life Cycle Engineering Sustainability and Remanufacturing VI, Busan, Korea, September 29 – October 1, 2008.
12. Rivera, J. L., D. J. Michalek, and J. W. Sutherland, “The Role of Nanotechnology in Sustainable Manufacturing,” Global Conference on Sustainable Product Development and Life Cycle Engineering Sustainability and Remanufacturing VI, Busan, Korea, September 29 – October 1, 2008.[PDF]
13. Shonnard, D. R., J. Jensen, J. Naber, Q. Zhang, A. Maclean, K. Halvorsen, T. Jenkins, C. Polonowski, and J. Sutherland, “Wood-to-Wheels: A Multidisciplinary Research Initiative in Sustainable Transportation Utilizing Fuels and Co-Products from Forest Resources,” (2008-21-0026), Convergence 2008, SAE International, October 20-22, 2008, Detroit, Michigan.[PDF]
2007
14. Rivera, J. L., D. J. Michalek, and J. W. Sutherland, "Air Quality In Manufacturing," Chapter 7 in Environmentally Conscious Manufacturing Handbook, John Wiley and Sons, 2007, pp. 145-178.[PDF]
15. Huntzinger, D. N., M. J. Hutchins, J. S. Gierke, and J. W. Sutherland, "Enabling Sustainable Thinking in Undergraduate Engineering Education," International Journal of Engineering Education, Vo. 23, No. 2, 2007, pp. 218-230. [PDF]
16. Xue, H., V. Kumar, and J. W. Sutherland, "Material Flow and Environmental Impacts of Manufacturing Systems via Aggregated Input-Output Models," Journal of Cleaner Production, Vol. 15, No. 13-14, 2007, pp. 1349-1358. [PDF]
17. Sutherland, J. W. and K. R. Haapala, "Optimization of Steel Production to Improve Lifecycle Environmental Performance," CIRP Annals, Vol. 56, No. 1, 2007, pp. 5-8.[PDF]
18. Kumar, V. and J. W. Sutherland, "Infrastructure Changes Required to Achieve Higher Material Recovery Targets from End-of-Use Vehicles," Trans. of NAMRI/SME, Vol. 35, 2007, pp. 201-208.
19. Kumar, V., P. S. Shirodkar, J. A. Camelio, and J. W. Sutherland, "Value Flow Characterization During Product Lifecycle to Assist in Recovery Decisions," International Journal of Production Research, Vol. 45, No. 18, 2007, pp. 4555-4572.
20. Filipovic, A. J. and J. W. Sutherland, "Assessing the Performance of a Magnetostrictive-Actuated Tool Holder to Achieve Axial Modulations with Application to Dry Deep Hole Drilling," Journal of Manufacturing Processes, Vol. 9, No. 2, 2007, pp. 75-86.[PDF]
21. Huang, J., K. Kalaitzidou, J. W. Sutherland, and E. C. Aifantis, "Validation of a Predictive Model for Adiabatic Shear Band Formation in Chips Produced via Orthogonal Machining," J. Mech. Behaviour of Materials, Vol. 18, No. 4, 2007, pp. 243-263. [PDF]
22. Johnson, D. M., L. Bohmann, K. Mattila, J. Sutherland, and S. Sorby, "Meeting the Needs of Industry: Service Systems Engineering Curriculum," Proceedings of 2007 DSI Mini-Conference in Service Science, sponsored by IBM and Bentley College at Carnegie Mellon, Pittsburgh, Pennsylvania, May 2007.
23. Sorby, S. A., L. J. Bohmann, D. M. Johnson, K. G. Mattila, and J. W. Sutherland, "Defining a Curriculum for Service Systems Engineering using a Delphi Technique," Proceedings of American Society for Engineering Education Conference, Honolulu, Hawaii, June 2007. [PDF]
24. Garcilaso, L., K. L. Jordan, V. Kumar, M. J. Hutchins, and J. W. Sutherland, "A Life-cycle Comparison of Clothes Washing Alternatives," Proceedings of CIRP International Conference on Life Cycle Engineering 2007, Tokyo, Japan, June 2007. [PDF]
25.
Bohmann, L., D. Johnson, K. Mattila,
26. Haapala, K. R., M. J. Hutchins, J. L. Rivera, V. Kumar, A. R. Clarke, T. D. Eatmon, R. A. Harris, M. H. Durfee, J. R. Mihelcic, D. R. Shonnard, and J. W. Sutherland, "Education, Research, and Training Aspects of the Sustainable Futures NSF IGERT Project," Proceedings of the 2007 ASEE North Midwest Sectional Conference, Houghton, Michigan, September 2007, appeared on CD-ROM. [PDF]
27. Adler, D. P., V. Kumar, P. A. Ludewig, J. W. Sutherland, "Comparing Energy & Other Measures of Environmental Performance in the Original Manufacturing and Remanufacturing of Engine Components," Proceedings of ASME Manufacturing Science and Engineering Conference, Atlanta, Georgia, October 2007, appeared on CD-ROM.[PDF]
28.
Sutherland J. W., "Global Manufacturing and
the Sustainability Challenge", Technology Century
Magazine, The Engineering Society of
2006
29. DeVor, R. E., T. H. Chang, and J. W. Sutherland, Statistical Quality Design and Control: Contemporary Concepts and Methods, Second Edition, Prentice-Hall, 2006, 942 pages.
30. Electronic version of Solutions Manual is available online at the Prentice-Hall website.
31. Adler, D. P., W. W.-S. Hii, D. J. Michalek, and J. W. Sutherland, "Examining the Role of Cutting Fluids in Machining and Efforts to Address Associated Environmental/Health Concerns," Machining Science and Technology, Vol. 10, No. 1, 2006, pp. 23-58.[PDF]
32. Zheng, Y., X. Hu, and J. W. Sutherland, "Application of Finite Deformation Theory to the Development of an Orthogonal Cutting Model, Part 1: Model Development," J. of Manf. Sci. and Engr., Trans. ASME, Vol. 128, No. 3, August 2006, pp. 760-766.
33. Zheng, Y., X. Hu, and J. W. Sutherland, "Application of Finite Deformation Theory to the Development of an Orthogonal Cutting Model, Part 2: Experimental Investigation and Model Validation," J. of Manf. Sci. and Engr., Trans. ASME, Vol. 128, No. 3, August 2006, pp. 767-774.
34. Kumar, V., K. R. Haapala, J. L. Rivera, M. J. Hutchins, W. J. Endres, J. K. Gershenson, D. J. Michalek, and J. W. Sutherland, "Infusing Sustainability Principles into Manufacturing/Mechanical Engineering Curricula," SME Journal of Manufacturing Systems, Vo. 24, No. 3, 2006, pp. 215-225. [PDF]
35. Hutchins, M J., and J. W. Sutherland, "The Role of the Social Dimension in Life Cycle Engineering," Proceedings of 13th CIRP International Conference on Life Cycle Engineering, Leuven, Belgium, 2006, pp. 55-60.[PDF]
36. Tumkor, S., V. Kumar, K. Haapala, J. W. Sutherland, "New Engineering Design Concepts for Sustainable Products," Proceedings of ASEE Annual Conference, Chicago, Illinois, June 2006, appeared on CD-ROM.
37.
Garcilaso, L R., Kumar, V., and J. W. Sutherland, "Achieving
Dematerialization via the Servicizing of Products," Proceedings
16th CIRP International Design Seminar,
38. Haapala, K., J. Rivera, and J. W. Sutherland, "Environmentally Responsible Process Selection via Life Cycle Analysis," Proceedings of International Symposium on Flexible Automation, Osaka, Japan, 2006, appeared on CD-ROM. [PDF]
39. Shirodkar, P. S., V. Kumar, M. E. Jarvie, and J. W. Sutherland, "Exploring Value Flow in the Product Life Cycle to Promote Successful Value Recovery," Proceedings of Sustainable Manufacturing IV - Global Conference on Sustainable Product Development and Life Cycle Engineering, Sao Carlos, Sao Paulo, Brazil, 2006, Paper #LCA02.
40. Sorby, S. A., L. J. Bohmann, T. D. Drummer, J. O. Frendewey, D. M. Johnson, K. G. Mattila, J. W. Sutherland, and R. O. Warrington, "Defining a Curriculum for Service Systems Engineering," Proceedings of IBM Service Science, Management, and Engineering (SSME) Conference, October 2006, appeared on CD-ROM.
2005
41. Gutowski, T., C. Murphy, D. Allen, D. Bauer, B. Bras, T. Piwonka, P. Sheng, J. Sutherland, D. Thurston, and E. Wolff, "Environmentally Benign Manufacturing: Observations from Japan, Europe and the United States," Journal of Cleaner Production, Vol. 13, January 2005, pp. 1-17. [PDF]
42. Filipovic, A. J., and J. W. Sutherland, "Development of a Magnetostrictive-Actuated Tool Holder for Dry Deep Hole Drilling," Transactions of NAMRI/SME, Vol. 33, 2005, pp. 437-444.
43. Dasch, J., J. D’Arcy, A. Gundrum, J. Sutherland, J. Johnson, and D. Carlson, "Characterization of Fine Particles from Machining in Automotive Plants," J. of Occupational and Environmental Hygiene, Vol. 2, No. 12, December 2005, pp. 609-625 [PDF].
44. Hokanson, D. R., J. R. Mihelcic, J. W. Sutherland, N. J. Hutzler, D. W. Watkins, J. K. Gershenson, D. J. Michalek, M. H. Durfee, D. R. Shonnard, K. L. Bradof, J. F. Chadde, C. L. Walck, R. A. Harris, K. Choudhury, and G. A. Joshi, "University Education Initiatives in Sustainability," Proceedings of Engineering Sustainability, Pittsburgh, Pennsylvania, 2005, appeared on CD-ROM.
45. Sorby, S. A., L. J. Bohmann, T. D. Drummer, J. O. Frendewey, K. G. Mattila, and J. W. Sutherland, "Development of a Curriculum for Service Systems Engineering Using a Delphi Technique," Proceedings of the Am. Society for Engr. Educ. Annual Conf. & Exposition, #2005-635, 2005, pp. 15085-15093.
46. Kumar, V., K. R. Haapala, J. L. Rivera, M. J. Hutchins, W. J. Endres, J. K. Gershenson, D. J. Michalek, and J. W. Sutherland, "Towards Manufacturing/ Mechanical Engineering Curricular Change in Support of a Sustainable Future," Looking Forward: Innovations in Manufacturing Engineering Education, CIMEC (CIRP International Manufacturing Engineering Education Conference) and 3rd SME International Conference on Manufacturing Education, San Luis Obispo California, 2005, pp. 50-58. [PDF]
47. Hu, X., J. W. Sutherland, and J. M. Boileau, "Characterizing the Effect of 319 Aluminum Microstructure on Machinability, Part 1: Model Development," Proc. of ASME Manufacturing Engineering Division, 2005, (IMECE2005-79653), appeared on CD-ROM.
48. Hu, X., J. W. Sutherland, and J. M. Boileau, "Characterizing the Effect of 319 Aluminum Microstructure on Machinability, Part 2: Model Validation," Proc. of ASME Manufacturing Engineering Division, 2005, (IMECE2005-79654), appeared on CD-ROM.
49. Ju, C., L. P. Keranen, K. R. Haapala, D. J. Michalek, and J. W. Sutherland,, "Issues Associated with MQL Implementation: Effect on Peripheral Milling Process Performance and Impact on Machining Economics," Proc. of ASME Manufacturing Engineering Division, Orlando, Florida, 2005, (IMECE2005-79259), appeared on CD-ROM.
50. Kumar, V., D. J. Bee, P. S. Shirodkar, B. P. Bettig, and J. W. Sutherland, "Towards Sustainable Product and Material Flow Cycles: Identifying Barriers to Achieving Product Multi-use and Zero Waste," Proc. of ASME Manufacturing Engineering Division, 2005, (IMECE2005-81347), appeared on CD-ROM. [PDF]
51.
Tumkor, S., V. Kumar, and J. W. Sutherland, "Electrical
and Electronic Equipment Recovery and Recycling in
2004
52. Bandivadekar, A.P., V. Kumar, K. L. Gunter, J. W. Sutherland, "A Model for Material Flows and Economic Exchanges within the U.S. Automotive Life Cycle Chain," Transactions of NAMRI/SME, Vol. 32, 2004, pp. 303-310, also appeared in SME Journal of Manufacturing System, Vol. 23, No. 1, 2004, pp. 22-29. [PDF]
53. Sutherland, J., K. Gunter, D. Allen, D. Bauer, B. Bras, T. Gutowski, C. Murphy, T. Piwonka, P. Sheng, D. Thurston, E. Wolff, "A Global Perspective on the Environmental Challenges Facing the Automotive Industry: State-of-the-Art and Directions for the Future," International Journal of Vehicle Design, Vol. 35, Nos. 1/2, 2004, pp. 86-110. [PDF]
54.
Weinert, K.,
55. Yue, Y., J. Sun, K. L. Gunter, D. J. Michalek, and J. W. Sutherland, "Character and Behavior of Mist Generated by Application of Cutting Fluid to a Rotating Cylindrical Workpiece, Part 1: Model Development," J. of Manf. Sci. and Engr., Trans. ASME, Vol. 126, No. 3, August 2004, pp. 417-425. [PDF]
56. Sun, J., C. Ju, Y. Yue, K. L. Gunter, D. J. Michalek, and J. W. Sutherland, "Character and Behavior of Mist Generated by Application of Cutting Fluid to a Rotating Cylindrical Workpiece, Part 2: Experimental Validation," J. of Manf. Sci. and Engr., Trans. ASME, Vol. 126, No. 3, August 2004, pp. 426-434. [PDF]
57. Michalek, D. J., J. W. Sutherland, W. W. S. Hii, J. Sun, L. A. Kukula, and C. Ju, "Continuous Improvements to Mist Reduction in the Machining Environment Using a Kinematic Coagulation System," Proceedings of the 2004 NSF Design, Service, and Manufacturing Grantees and Research Conference, Dallas, Texas, January 2004, appeared on CD-ROM.
58. Ju, C., X. Hu, D. J. Michalek, and J. W. Sutherland, "Reducing the Use of Cutting Fluids In Machining Operations," International Symposium on Ecological Challenge in Manufacturing Systems, Keio University, Yokohama, Japan, February, 2004.
59. Kinare, S. S., D. J. Michalek, C. Ju, J. Sun, and J. W. Sutherland, "An Experimental Investigation of Cutting Fluid Mist Removal via a Novel Atomizer System," Environmental Sustainability in the Mobility Industry: Technology and Business Challenges, SAE SP-1865, March 2004.
60. Xue, H., V. Kumar, S. M. Pandit, and J. W. Sutherland, "An Enhanced Input-Output Model for Material Flow Analysis of Manufacturing Processes," Japan-USA Symposium for Flexible Automation, 2004, appeared on CD-ROM. [PDF]
61. Haapala, K. R., K. N. Khadke, and J. W. Sutherland, "A Framework for Predicting Manufacturing Waste Production and Energy Consumption in Product Design," Proceedings from: Global Conference on Sustainable Product Development and Life Cycle Engineering, Berlin, Germany, 2004, pp. 243-250.
62. Gunter, K. L. and J. W. Sutherland, "Analytical Models for Economic Demanufacturing Inventory Management," Proc. of ASME Manufacturing Engineering Division, 2004, (IMECE2004-61446), appeared on CD-ROM.
2003
63. Behm, S. U., K. L. Gunter, and J. W. Sutherland, "An Investigation into the Effect of Process Parameter Settings on Air Emission Characteristics in the Lost Foam Casting Process," AFS Transactions, 2003, Paper #03-031, appeared on CD-ROM. [PDF]
64. Sutherland, J. W., K. L. Gunter, K. R. Haapala, K. Khadke, S. J. Skerlos, J. B. Zimmerman, W. W. Olson, and R. Sadasivuni, "Environmentally Benign Manufacturing: Status and Vision for the Future," Transactions of NAMRI/SME, 2003, pp. 345-352, also appeared as SME Paper MR03-188. [PDF]
65. Michalek, D. J., W. W. S. Hii, J. Sun, K. L. Gunter, and J. W. Sutherland, "Experimental and Analytical Efforts to Characterize Cutting Fluid Mist Formation and Behavior in Machining," Applied Occupational and Environmental Hygiene, Vol. 18, No. 11, 2003, pp. 842-854. [PDF]
66. Mihelcic, J. R., J. C. Crittenden, M. J. Small, D. R. Shonnard, D. R. Hokanson, Q. Zhang, H. Chen, S. A. Sorby, V. U. James, J. W. Sutherland, and J. L. Schnoor, "Sustainability Science and Engineering: The Emergence of a New Metadiscipline," Environmental Science & Technology, Vol. 37, No. 23, 2003, pp. 5314-5324. [PDF]
67.
Michalek, D. J., J. W. Sutherland, C. Ju, W. Hii,
S. Kinare, and J. Sun, "Update on Mist Reduction in Machining via
Kinematic Coagulation," Proceedings of the 2003 NSF
Design & Manufacturing Grantees Conference,
68.
Gunter, K. L., D. J. Bee, and J. W. Sutherland, "Inventory
Management in Demanufacturing Facilities," Proceedings
Colloquium e-ecological
69. Sutherland, J. W., V. Kumar, J. C. Crittenden, M. H. Durfee, J. K. Gershenson, H. Gorman, D. R. Hokanson, N. J. Hutzler, D. J. Michalek, J. R. Mihelcic, D. R. Shonnard, B. D. Solomon, S. Sorby, "An Education Program in Support of a Sustainable Future," Proc. of ASME/IMECE, MED Vol. 14, 2003, pp. 611-618, (IMECE2003-43422), appeared on CD-ROM. [PDF]
2002
70.
Allen, D., D. Bauer, B. Bras, T. Gutowski, C.
Murphy, T. Piwonka, P. Sheng, J. Sutherland, D. Thurston, and E. Wolff, "Environmentally
Benign Manufacturing: Trends In Europe, Japan and the USA," J. of Manf. Sci. and Engr., Trans ASME, Vol. 124, No. 4,
November 2002, pp. 908-920, originally appeared in Proc. of ASME DETC: Design
Engineering Technical Conference,
71. Cao, T., and J. W. Sutherland, "Investigation of Thread Tapping Load Characteristics through Mechanistic Modeling and Experimentation," International Journal of Machine Tools and Manufacture, Vol. 42, No. 14, November 2002, pp. 1527-1538.
72. Chan, W., K. L. Gunter, and J. W. Sutherland, "An Experimental Study of the Fume Particulate Produced by the Shielded Metal Arc Welding Process," Transactions of NAMRI/SME, Vol. 30, 2002, pp. 581-588, also appeared as SME Technical Paper, No. MS02-201. [PDF]
73. Li, K., X. L. Gao, and J. W. Sutherland, "Finite Element Simulation of the Orthogonal Metal Cutting Process for Qualitative Understanding of the Effects of Crater Wear on the Chip Formation Process," Journal of Materials Processing Technology, Vol. 127, No. 3, 2002, pp. 309-324.
74. Ranganath, S., and J. W. Sutherland, "An Improved Method for Cutter Runout Modeling in the Peripheral Milling Process," Machining Science and Technology, Vol. 6, No. 1, 2002, pp. 1-20.
75. Sutherland, J. W., and K. L. Gunter, "A Model for Improving Economic Performance of a Demanufacturing System for Reduced Product End-of-Life Environmental Impact," submitted by K. J. Weinmann, Annals of CIRP, Vol. 51/1, 2002, pp. 45-48.
76. Bandivadekar, A. P., K. L. Gunter, and J. W. Sutherland, "A Model for Material Flows and Economic Exchanges Within the U.S. Automotive Life-Cycle Chain and its Sensitivity to Systemic Changes," Proceedings of 9th CIRP International Seminar on Life Cycle Engineering, Erlangen, Germany, April 2002, pp. 181-189.
77. Batzer, S. A., G. Subhash, W. Olson, and J. W. Sutherland, "Large Strain Constitutive Model Development with Application to Orthogonal Machining," Proceedings of the 6th CIRP International Workshop on Modeling of Machining Operations, West Lafayette, Indiana, May 2002.
78. Bekkala, G., S. Pandit, and J. Sutherland, "A Framework for Characterizing the Impact of Product Design Decisions on Environmental Performance," Proceedings of Japan-USA Symposium on Flexible Automation, 2002, pp. 1369-1376.
79. Ju, C., J. Sun, D. J. Michalek, and J. W. Sutherland, "Application of an Imaging System to Study Machining Mist Formation via an Atomization Mechanism," Proc. ASME IMECE, DSC Vol. 71, November 2002, appeared on CD-ROM, IMECE2002-32033.
80. Michalek, D., J. Sutherland, W. Hii, C. Ju, S. Kinare, and J. Sun, "Investigation of a Kinematic Coagulation Mechanism to Improve Air Quality in Machining Environments," Proc. of the 2002 NSF Design & Mfg. Grantees Conf., January 2002, appeared on CD-ROM.
81. Olson, W. W., and J. W. Sutherland, "National Science Foundation Workshop on Environmentally Benign Manufacturing for the Transportation Industries," Proc. of SAE World Congress, March 2002, SAE paper #2002-01-0593.
82. Pandit, S. M., J. W. Sutherland, and G. A. Bekkala, "Modeling for Environmental Impacts using Experimental Data," Envirosoft: Ninth International Conference on The Modeling, Monitoring and Management of Environmental Problems, Bergen, Norway, May 2002, pp. 381-392.
2001
83. Sutherland, J. W., and K. L. Gunter, "Environmental Attributes of Manufacturing Processes," Chapter 13 in Handbook of Environmentally Conscious Manufacturing, Ed. C. N. Madu, Kluwer Acad. Pub., 2001, pp. 293-316.
84. Batzer, S. A., and J. W. Sutherland, "A Geometric Analysis of Semi-spiral Chip Morphology in Orthogonal Machining," Machining Science and Technology, Vol. 5, No. 1, 2001, pp. 63-76.
85. Eppert, J. J., K. L. Gunter, and J. W. Sutherland, "Development of a Cutting Fluid Classification System Using Cluster Analysis," Tribology Transactions, Vol. 44, No. 3, 2001, pp. 375-382.
86. Li, J., and J. W. Sutherland, "Multi-Channel Dynamic Data Collecting System of Rotors," Journal of Modelling, Measurement & Control, Series B, Vol. 70, No. 4, 2001, pp. 1-10.
87. Li, J., X. Zhang, and J. W. Sutherland, "Identification of Gear Transmission System Dynamics; Part I: Model Development," Journal of Advances in Modelling & Analysis, Series C, Vol. 56, No. 1, 2001, pp. 1- 12.
88. Shen, G., A. Gandhi, O. Arici, and J. W. Sutherland, "A Model for Workpiece Temperatures During Peripheral Milling Including the Effect of Cutting Fluids," Trans. of NAMRI/SME, Vol. 29, May 2001, pp. 265-272, also appeared as SME Technical Paper, No. MR01-269, 2001.
89. Salisbury, E. J., K. V. Domala, K. S. Moon, M. H. Miller, and J. W. Sutherland, "A Three-Dimensional Model for the Surface Texture in Surface Grinding, Part I: Surface Generation Model," J. of Manf. Sci. and Engr., Trans. ASME, Vol. 123, November 2001, pp. 576-581. [PDF]
90. Salisbury, E. J., K. V. Domala, K. S. Moon, M. H. Miller, and J. W. Sutherland, "A Three-Dimensional Model for the Surface Texture in Surface Grinding, Part II: Grinding Wheel Surface Texture Model," J. of Manf. Sci. and Engr., Trans. ASME, Vol. 123, November 2001, pp. 582-590. [PDF]
91. Siow, Y. K., S. L. Yang, and J. W. Sutherland, "Analysis of Cutting Fluid Jet Impingement on a Flat Surface via Computational Fluid Dynamics," Intl. Jour. for Mfg. Sci. and Technology, Vol. 2, No. 2, 2001, pp. 143-152. [PDF]
92. Gershenson, J. K., B. D. Solomon, D. R. Shonnard, D. W. Watkins, and J. W. Sutherland, "Production Decision Making in the Face of Uncertainty about Air Toxics Regulation and Global Climate Change Policy," Proc. of ASME IMECE, Vol. TS-6, November 2001, pp. 75-84.
93. Huang, J., K. Kalaitzidou, J. W. Sutherland, W. W. Milligan, E. C. Aifantis, R. Sievert, and S. Forest "Gradient Plasticity: Implications to Chip Formation in Machining," Proceedings of 4th Int. ESAFORM Conf. on Material Forming, Liege, Belgium, April 2001, pp. 527-530.
94.
King, N., L. Keranen, K. Gunter, and J. Sutherland,
"Wet Versus Dry Turning: A Comparison of Machining Costs, Product Quality,
and Aerosol Formation," Technical Paper 2001-01-0343, Proceedings
of 2001 SAE World Congress,
95. Shapton, W. R., P. F. Zenner, W. W. Predebon, J. W. Sutherland, M. A. Banks-Sikarskie, L. A. Artman, and P. A. Lins, "From the Classroom to the Boardroom: Distance Learning Undergraduate and Graduate Engineering Programs: A Global Partnership of Industry and Academia," International Conference on Engineering Education, Session 8B1, Oslo, Norway, August 2001, 8B1: pp. 7-12. [PDF]
96. Shen, G., O. Arici, and J. W. Sutherland, "Development of a Model for the Prediction of the Energy Partition in a Peripheral Milling Operation," IMECE Proc. of ASME: Manufacturing Engineering Division, ASME Bound Volume - MED Vol. 12, November 2001, distributed on CD-ROM.
97. Sutherland, J., D. Michalek, S. Behm, W. Chan, K. Gunter, X. Hu, C. Ju, N. King, V. Kulur, G. Shen, "Assessing Airborne Emissions of Machining, Casting, and Welding Operations," Proc. of the 2001 NSF Design & Mfg. Grantees Conf., January 2001, Tampa, Florida, distributed on CD-ROM.
98. Thurston, D., T. Gutowski, C. Murphy, Allen, D., D. Bauer, B. Bras, D. Durham, P. Sheng, J. Sutherland, and E. Wolff, "U.S. National Science Foundation Panel Report on Status of International Environmentally Benign Manufacturing Technologies," Proceedings of the 13th International Conference on Engineering Design, Glasgow, Scotland, August 2001, pp. 605-612.
2000
99. Bergstrom, A., A. Filipovic, W. W. Olson, and J. W. Sutherland, "Mechanistic Prediction of Drilling Forces Incorporating a Minimum Cutting Energy Model for Chip Flow Angle," Trans. of NAMRI/SME, Vol. 28, May 2000, pp. 143-148, also appeared as SME Technical Paper No. MR00-193, 2000. [PDF]
100. Zheng, Y., H. Li, W. W. Olson, and J. W. Sutherland, "Evaluating Cutting Fluid Effects on Cylinder Boring Surface Errors by Inverse Heat Transfer and Finite Element Methods," J. of Manf. Sci. and Engr., Trans. ASME, Vol. 122, No. 3, August 2000, pp. 377-383. [PDF]
101. Sutherland, J. W., V. N. Kulur, and N. C. King (submitted by B. F. Von Turkovich), "An Experimental Investigation of Air Quality in Wet and Dry Turning," Annals of CIRP, Vol. 49/1, August 2000, pp. 61-64. [PDF]
102. Li, J., and J. W. Sutherland, "Multi-Channel Data Transmission System for Rotating Elements Using a Non-Contacting Slip Ring," Review of Scientific Instruments, Vol. 71, No. 11, November 2000, pp. 4319 - 4322. [PDF]
103. Li, J., F. Liu, and J. W. Sutherland, "Identification of Gear Transmission System Dynamics. Part II: Model Validation," Journal of Advances in Modelling & Analysis, Series C, Vol. 55, No. 4, 2000, pp. 1-12.
104.
Filipovic, A. J., W. W. Olson, S. M. Pandit, and J.
W. Sutherland, "Modeling of Cutting Fluid System Dynamics," Proc. of the 2000 Japan - U.S.A. Symposium on Flexible Automation,
105. Kuchibhotla, R. M., J. F. Schultze, and J. W. Sutherland, "An Investigation of the Effects of Lubricant Viscosity, Surface Finish, and Clearance on Machine Tool Slide-way Damping and Friction," IMAC-XVIII: Conf. & Exposition on Structural Dynamics, San Antonio, Texas, February 2000, pp. 433-439. [PDF]
106. Sutherland, J. W., A. Gandhi, V. Kulur, W. K. Chan, and Y-K. Siow, "Cutting Fluids in Machining: Heat Transfer and Mist Formation Issues," Proc. of the 2000 NSF Design & Mfg. Grantees Conf., January 2000, distributed on CD-ROM. [PDF]
107. Xue, H., A. J. Filipovic, S. M. Pandit, and J. W. Sutherland, "Using a Manufacturing Process Classification System for Improved Environmental Performance," Environmental Concepts for the Automotive Industry, SAE publ. SP-1542, Technical Paper 2000-01-0020, SAE World Congress, Detroit, Michigan, March 2000. [PDF]
108. Xue, H., S. M. Pandit, and J. W. Sutherland, and W. W. Olson, "Input-Output Modeling for Environmental Impact Analysis of Manufacturing Processes," Proc. of the 2000 Japan - U.S.A. Symposium on Flexible Automation, Ann Arbor, Michigan, July 2000, distributed on CD-ROM, Paper #2000JUSFA-13231.
109. Yue, Y., K. L. Gunter, D. J. Michalek, J. W. Sutherland, "Cutting Fluid Mist Formation in Turning Via Automization Part I: Model Development," IMECE Proc. of ASME: Manufacturing Engineering Division, ASME Bound Volume - MED Vol. 11, November 2000, pp. 843-850.
110. Yue, Y., K .L. Gunter, D. J. Michalek, and J. W. Sutherland, "Cutting Fluid Mist Formation in Turning Via Automization Part II: Experimental Validation," IMECE Proc. of ASME: Manufacturing Engineering Division, ASME Bound Volume - MED Vol. 11, November 2000, pp. 851-858.
1999
111. Gunter, K. L. and J. W. Sutherland, "An Experimental Investigation into the Effect of Process Conditions on the Mass Concentration of Cutting Fluid Mist in Turning," Journal of Cleaner Production, Vol. 7, No. 5, 1999, pp. 341-350. [PDF]
112. Yue, Y., K. L. Gunter, D. J. Michalek, and J. W. Sutherland, "An Examination of Cutting Fluid Mist Formation in Machining," Trans. of NAMRI/SME, Vol. 27, May 1999, pp. 221-226, also appeared as SME Technical Paper No. MS99-180, 1999. [PDF]
113. Cozzens, D. A., P. D. Rao, W. W. Olson, J. W. Sutherland, and J. M. Panetta, "An Experimental Investigation into the Effect of Cutting Fluid Conditions on the Boring of Aluminum Alloys," J. of Mfg. Sci. & Engr., Trans. ASME, Vol. 121, No. 3, August 1999, pp. 434-439. [PDF]
114. Melkote, S. N., J. W. Sutherland, and C. King, "The Effect of Tool Flexibility on Back-Cutting in End Milled Surfaces," J. of Mfg. Sci. & Engr., Trans. ASME, Vol. 121, No. 3, August 1999, pp. 532-537. [PDF]
115. Ranganath, S., K. Narayanan, and J. W. Sutherland, "The Role of Flank Face Interference in Improving the Accuracy of Dynamic Force Predictions in Peripheral Milling," J. of Manf. Sci. and Engr., Trans. ASME, Vol. 121, No. 4, November 1999, pp. 593-599. [PDF]
116. Sutherland, J. W., T. Cao, A. Gandhi, P. Sheng, D. Bauer, R. E. DeVor, S. G. Kapoor, and S. Skerlos, "Web-Based Cutting Fluid Evaluation Software," Proceedings of 31st CIRP International Seminar on Manufacturing Systems, May 1998, Berkeley, CA, pp. 501-505, also appeared in CIRP Journal of Manufacturing Systems, Vol. 29, No. 6, 1999, pp. 517-521. [PDF]
117. Cao, T., S. A. Batzer, and J. W. Sutherland, "Effects of Cutting Fluid Composition on the Dimensional Accuracy of Tapped Threads," Technical Papers of NAMRI/SME, Vol. 27, May 1999, pp. 95-100, also appeared as SME Technical Paper No. MS99-143, 1999. [PDF]
118. Zheng, Y., and J.W. Sutherland, "An Orthogonal Cutting Model Based on Finite Deformation Analysis Part I: Model Development," Proc. of IMECE: Manufacturing Science and Engineering, ASME Bound Volume - MED Vol. 10, November 1999, pp. 293-300. [PDF]
119. Zheng, Y., and J. W. Sutherland, "An Orthogonal Cutting Model Based on Finite Deformation Analysis Part II: Constitutive Equations and Experimental Verification," Proc. of IMECE: Manufacturing Science and Engineering, ASME Bound Volume - MED Vol. 10, November 1999, pp. 301-309. [PDF]
120. Sutherland, J. W., K. L. Gunter, Y. Yue, A. Gandhi, and Y. K. Siow, "The Role of Cutting Fluids in Machining: Modeling Mist Formation and Heat Transfer Effects," Proc. of the 1999 NSF Design & Mfg. Grantees Conf., January 1999, distributed on CD-ROM. [PDF]
121. Filipovic, A., H. Xue, J. Zeng, J. Wang, W. W. Olson, S. M. Pandit, and J. W. Sutherland, "ECDM Input- Output Analysis with Markovian Decision Making," Proc. of the 1999 NSF Design & Mfg. Grantees Conf., January 1999, distributed on CD-ROM. [PDF]
122. Huang, J., J. W. Sutherland, and E. C. Aifantis, "Application of Gradient Theory in Machining: Localized Chip Formation," Proc. of Plasticity’ 99: The Seventh International Symposium on Plasticity and its Current Applications, January 1999, pp. 353-356. [PDF]
123. Olson, W. W., A. Filipovic, J. W. Sutherland, and S. M. Pandit, "Reduction of the Environmental Impact of Essential Manufacturing Processes," Proc. of the 1999 SAE International Congress and Exposition, Detroit, Michigan, 1999. SAE Technical Paper: 1999-01-0355. [PDF]
124. Gunter, K. L., Y. Yue, D. J. Michalek, and J. W. Sutherland, "Cutting Fluid Atomization to Form Mist in Turning Operations," 12th Annual Conference of Liquid Atomization and Spray Systems (ILASS), May 1999, pp. 111-115. [PDF]
125. Basu, S. and J. W. Sutherland, "Multi-objective Decision Making in Environmentally Conscious Manufacturing," Proceedings of 6th CIRP International Seminar on Life Cycle Engineering, June 1999, pp. 323-331. [PDF]
1998
126. Wentland, C. J., N. Soni, W. W. Olson, and J. W. Sutherland, "Development and Application of a Reprocessability Index System for Discrete Rotational Parts," Engineering Design and Automation, Vol. 4, No. 1, 1998, pp. 47-55. [PDF]
127. Wang, Y., G. Zhang, K. S. Moon, and J. W. Sutherland, "Compensation for the Thermal Error of a Multi-axis Machining Center," Journal of Matls. Processing Tech., Vol. 75/1-3, March 1998, pp. 45-53. [PDF]
128. Ranganath S., D. Liu, and J. W. Sutherland, "A Comprehensive Model for the Flank Face Interference Mechanism in Peripheral Milling," Trans. of NAMRI/SME, Vol. 26, May 1998, pp. 249-254. [PDF]
129. Daniel, C. M., W. W. Olson, and J. W. Sutherland, "Modeling the Effects of Component Level Geometric and Form Deviations on Machine Tool Slideway Errors," Trans. of NAMRI/SME, Vol. 26, May 1998, pp. 347-352, also appeared as SME Technical Paper No. MS98-266, 1998. [PDF]
130. Liu, D., J. W. Sutherland, K. S. Moon, T. J. Sturos, and A. R. Kashani, "Surface Texture Improvement in the Turning Process via Application of a Magnetostrictively Actuated Tool Holder," Trans. ASME, J. of Dyn. Sys., Meas., and Control, Vol. 120, June 1998, pp. 193-199. [PDF]
131. Batzer, S. A., D. M. Haan, P. D. Rao, W. W. Olson, and J. W. Sutherland, "Chip Morphology and Hole Texture in the Drilling of Cast Aluminum Alloys," Journal of Matls. Processing Tech., Vol. 79/1-3, July 1998, pp. 72-78. [PDF]
132.
Yue, Y., Y. Zheng, S. Basu, and J. W. Sutherland, "Cutting
Fluids: Performance Measures and Health Related Characteristics," Proc. of the
133. Olson, W. W., J. B. Wang, J. Zeng, and J. W. Sutherland, "Reducing Manufacturing Impacts on the Environment with Markov Decision Making," Proc. of the Japan - U.S.A. Symposium on Flexible Automation, July 1998, pp. 191-198. [PDF]
134. Filipovic, A. J., H. Gowaikar, W. W. Olson, S. M. Pandit, and J. W. Sutherland, "Characterization of Cutting Fluid System Dynamics," Proc. of IMECE: Manufacturing Science and Engineering, ASME Bound Volume - MED Vol. 8, November 1998, pp. 389-395. [PDF]
135. Liu, D., and J. W. Sutherland, "Active Vibration Abatement in a Turning Process by Applying a Magnetostrictively Actuated Tool Holder," Proc. of IMECE: Manufacturing Science and Engineering, ASME Bound Volume - MED Vol. 8, November 1998, pp. 131-140. [PDF]
136. Sutherland, J. W., Y. Yue, Y. Zheng, K. Gunter, and T. Cao, "Evaluation of Environmental Effects and Process Impact of Cutting Fluids," Proc. of the 1998 NSF Design & Mfg. Grantees Conf., 1998, pp. 369-370. [PDF]
137. Olson, W. W., S. M. Pandit, J. W. Sutherland, and H. Xue, "Life Cycle Analysis Using Input-Output Analysis with Markov Decision Processes," Proc. of the 1998 NSF Design & Mfg. Grantees Conf., 1998, pp. 9-10. [PDF]
138. Yue, Y., J. W. Sutherland and D. J. Michalek, "Cutting Fluid Mist Formation During Machining Process via Atomization," 11th Annual Conference of Liquid Atomization and Spray Systems (ILASS), 1998, pp. 329-333. [PDF]
139. Olson, W. W., S. A. Batzer, and J. W. Sutherland, "Modeling of Chip Dynamics in Drilling," Proceedings of CIRP International Workshop on Modeling of Machining Operations, May 1998, Atlanta, Georgia, pp. 347-361. [PDF]
140. Batzer, S. A., and J. W. Sutherland, "The Dry Cure for Coolant Ills," Cutting Tool Engineering, June 1998, pp. 34, 36-38, 42, 44.
141.
Sutherland, J. W.,
1997
142. Sutherland, J. W., T. Cao, C. M. Daniel, Y. Yue, Y. Zheng, P. Sheng, D. Bauer, M. Srinivasan, R. E. DeVor, S. G. Kapoor, and S. Skerlos, "CFEST: An Internet-Based Cutting Fluid Evaluation Software Testbed," Trans. of NAMRI/SME, Vol. 25, May 1997, pp. 243-248. [PDF]
143. Batzer, S. A., J. W. Sutherland, and W. W. Olson, "Chip Morphology and Bending Moment Models for Orthogonal Machining with Flat Faced Tools," Trans. of NAMRI/SME, Vol. 25, May 1997, pp. 231-236. [PDF]
144. Sutherland, J. W., E. J. Salisbury, and F. W. Hoge, "A Model for the Cutting Force System in the Gear Broaching Process," Int. J. of Mach. Tools and Manufacture, Vol. 37, No. 10, 1997, pp. 1409-1421. [PDF]
145. Haan, D. M., S. A. Batzer, W. W. Olson, and J. W. Sutherland, "An Experimental Study of Cutting Fluid Effects in Drilling," Journal of Matls. Processing Tech., Vol. 71/2, November 1997, pp. 305-313. [PDF]
146. Daniel, C. M., W. W. Olson, and J. W. Sutherland, "Research Advances in Dry and Semi-Dry Machining," SAE Technical Paper No. 970415, also in the SAE Trans., J. of Materials and Manufacturing, Vol. 106, 1997, pp. 373-383. [PDF]
147. Milacic, D., H. A. Gowaikar, W. W. Olson, and J. W. Sutherland, "A Proposed LCA Model of Environmental Effects with Markovian Decision Making," SAE Technical Paper No. 971174, also in the SAE Trans., J. of Passenger Cars, Vol. 106, 1997, pp. 2174-2181. [PDF]
148. Ehmann, K. F., R. E. DeVor, E. C. DeMeter, D. A. Dornfeld, S. G. Kapoor, J. Ni, K. P. Rajurkar, Y. Shin, and J. W. Sutherland, "A Framework for a Virtual Machine Tool (VMT)," Technical Papers of NAMRI/SME, May 1997, pp. 143-148. [PDF]
149. Saxena, V., D. Liu, C. M. Daniel, and J. W. Sutherland, "A Simulation Study of the Workspace and Dexterity of a Stewart Platform Based Machine Tool," Proc. of the ASME Dynamic Systems and Control Division, ASME Bound Volume - DSC Vol. 61, November 1997, pp. 617-623. [PDF]
150. Cao, T., S. A. Batzer, and J. W. Sutherland, "Experimental Investigations of Tapped Thread Surface Roughness for Cast Aluminum Alloys," Manf. Sci. and Engr., ASME Bound Volume - MED Vol. 6-1, November 1997, pp. 189-195. [PDF]
151. Zheng, Y., J. W. Sutherland, and W. W. Olson, "A Continuum Mechanics Model to Predict Shear Angle and Cutting Forces in Orthogonal Cutting," Manf. Sci. and Engr., ASME Bound Volume - MED Vol. 6-2, November 1997, pp. 61-68. [PDF]
152. Narayanan, K., S. Ranganath, and J. W. Sutherland, "A Dynamic Model of the Cutting Force System in Peripheral Milling Characterizing the Effects of Flank Face Interference," Manf. Sci. and Engr., ASME Bound Volume - MED Vol. 6-2, November 1997, pp. 143-151. [PDF]
153. Wang, Y., K. S. Moon, and J. W. Sutherland, "Theoretical Examination of a New Calibration Method for Multi-axis Machines," Manf. Sci. and Engr., ASME Bound Volume - MED Vol. 6-2, November 1997, pp. 427-433. [PDF]
154. Sutherland, J. W., C. M. Daniel, S. Vadrevu, and W. W. Olson, "Evaluating Reuse and Remanufacturing Potential Using a Simple Model for Product Value," Concurrent Product Design and Environmentally Conscious Manufacturing, ASME Bound Volume - DE Vol. 89 / MED Vol. 5, November 1997, pp. 263-274. [PDF]
155. Sutherland, J. W., Y. Yue, and Y. Zheng, "Modeling Mist Formation and Heat Generation to Achieve Environmentally Conscious Machining," Proc. of the 1997 NSF Design & Mfg. Grantees Conf., 1997, pp. 201-202. [PDF]
156. Daniel, C. M., J. W. Sutherland, and W. W. Olson, "A Model of the Tracking Errors of a Machine Tool Slideway," Proc. of 12th Annual Meeting of Am. Soc. for Prec. Engr., October 1997, pp. 65-68. [PDF]
1996
157. Zheng, Y., J. W. Sutherland, and W. W. Olson, "A Predictive Heat Generation Model in Orthogonal Cutting Visco-Plastic Material," Journal of the Mechanical Behavior of Materials, Vol. 6, No. 3, 1996, pp. 245-261. [PDF]
158. Philipps, K, W. W. Olson, and J. W. Sutherland, "Shearing of Automotive Grade Polypropylene and Acrylonitrile-Butadiene Styrene to Facilitate Recycling," Trans. of NAMRI/SME, Vol. 24, May 1996, pp. 217-222. [PDF]
159. Huang, J., W. W. Olson, J. W. Sutherland, and E. C. Aifantis, "On the Shear Instability in Chip Formation in Orthogonal Machining," Journal of the Mechanical Behavior of Materials, Vol. 7, No. 4, 1996, pp. 279-292. [PDF]
160. Wentland, C. J., W. W. Olson, and J. W. Sutherland, "Use of a Reprocessability Index System for the Environmental Scoring of Rotational Parts," Technical Papers of NAMRI/SME, May 1996, pp. 145-150, also appeared as SME Technical Paper No. MS96-133, 1996. [PDF]
161. Kashani, A. R., and J. W. Sutherland, "Adaptive Feedforward Control for Periodic Disturbance Rejection with Application to Machining Processes," Technical Papers of NAMRI/SME, May 1996, pp. 181-186, also appeared as SME Technical Paper No. MS96-138, 1996. [PDF]
162. Daniel, C. M., K. V. C. Rao, W. W. Olson, and J. W. Sutherland, "Effect of Cutting Fluid Properties and Application Variables on Heat Transfer in Turning and Boring Operations," Proc. of the Japan - U.S.A. Symposium on Flexible Automation, July 1996, pp. 1119-1126. [PDF]
163. Domala, K. V., E. J. Salisbury, K. S. Moon, and J. W. Sutherland, "The Frequency Component Structure of a 3-D Grinding Wheel Surface and its Effect on Ground Surface Texture," Proc. of the Japan - U.S.A. Symposium on Flexible Automation, July 1996, pp.1173-1180. [PDF]
164. Wang, Y., K. S. Moon, and J. W. Sutherland, "Evaluation of Elliptical Profiles and its Application in Cylinder Measurement by CMMs," Proceedings of the Annual Meeting of the American Society for Precision Engineering, October 1996, pp. 263-266. [PDF]
165. Yue, Y., J. W. Sutherland, and W. W. Olson, "Cutting Fluid Mist Formation in Machining Via Atomization Mechanisms," Proc. of Symp. on Design for Manf. and Assembly, ASME Bound Volume - DE Vol. 89, November 1996, pp. 37-46. [PDF]
166. Kanizar, W. L., D. Liu, K. S. Moon, and J. W. Sutherland, "A Magnetostrictive Based Micropositioner and its Application in Turning," Proc. of SPIE Symposium on Smart Structures and Materials, Vol. 2721, March 1996, pp. 385-393. [PDF]
167. Huang, J., G. Frantziskonis, W. W. Olson, J. W. Sutherland, and E. C. Aifantis, "Scale Effects and Material Heterogeneity via Wavelet Analysis," 19th International Congress on Theoretical and Applied Mechanics, Kyoto, Japan, August 1996.
168. Liu, D., and W. L. Kanizar, K. S. Moon, and J. W. Sutherland, "Application of a Magnetostrictive Based Cutting Tool Micropositioner for Non-circular Turning," Proc. of 2nd S. M. Wu Symposium on Manufacturing Science, May 1996, pp. 37-42. [PDF]
169. Batzer, S. A., P. D. Rao, D. M. Haan, W. W. Olson, and J. W. Sutherland, "An Experimental Investigation of Chip Morphology in Drilling," Proc. of 2nd S. M. Wu Symposium on Manufacturing Science, May 1996, pp. 102-107. [PDF]
170. Cao, T., J. W. Sutherland, and Y. Zheng, "An Experimental Investigation into the Effect of Joint Conditions on Structural Damping with Application to Machine Tools," Proc. of 2nd S. M. Wu Symposium on Manufacturing Science, May 1996, pp. 122-127. [PDF]
171. Moon, K. S., M. H. Miller, A. Chandra, and J. W. Sutherland, "Abrasives work at MTU," Abrasives Magazine, June/July 1996, pp. 17, 27-29.
1995
172. Matulis, R. J., F. K. McKeith, J. W. Sutherland, and M. S. Brewer, "Sensory Characteristics of Frankfurters as Affected by Fat, Salt, and pH," J. of Food Science, Vol. 60, No. 1, 1995, pp. 42-47. [PDF]
173. Matulis, R. J., F. K. McKeith, J. W. Sutherland, and M. S. Brewer, "Sensory Characteristics of Frankfurters as Affected by Salt, Fat, Soy Protein, and Carrageenan," J. of Food Science, Vol. 60, No. 1, 1995, pp. 48-54. [PDF]
174. Savage, W. D, L. S. Wei, J. W. Sutherland, and S. J. Schmidt, "Biologically Active Components Inactivation and Protein Insolubilization during Heat Processing of Soybeans," J. of Food Science, Vol. 60, No. 1, 1995, pp. 164-168, 180. [PDF]
175. Salisbury, E. J., K. S. Moon, and J. W. Sutherland, "Development of a Microscopic Laser Interferometry System for Precision Surface Measurement," J. Eng. for Ind., Trans. ASME, Vol. 117, November 1995, pp. 619-624, also in Contact Problems and Surface Interaction in Manufacturing and Tribological Systems, ASME Bound Volume - PED Vol. 67, December 1993, pp. 333-341, authors: K. S. Moon, E. J. Salisbury, and J. W. Sutherland. [PDF]
176.
177. Wang, Y., K. S. Moon, J. W. Sutherland, G. Zhang, Y. Zang, X. Chu, and J. Du, "Error Compensation of Multi-axis Manufacturing Center," Proceedings of the Annual Meeting of the American Society for Precision Engineering, October 1995, pp. 132-135. [PDF]
178. Whitmer, C. I., W. W. Olson, and J. W. Sutherland, "Determination of Design Effort Distribution for an Environmentally Conscious Product Using a Pairwise Comparison Approach," Manf. Sci. and Engr., ASME Bound Volume - MED Vol. 2-2/MH Vol. 3-2, November 1995, pp. 847-854. [PDF]
179. Cozzens, D. A., W. W. Olson, J. W. Sutherland, and J. M. Panetta, "An Experimental Investigation into the Effect of Cutting Fluid Conditions on the Boring of Aluminum Alloys," Concurrent Product and Process Engineering, ASME Bound Volume - MED Vol. 1/DE Vol. 85, November 1995, pp. 251-257.
180. Domala, K. V., E. J. Salisbury, K. S. Moon, and J. W. Sutherland, "A Three-Dimensional Geometric Model for the Surface Texture Generated by a Single Pass of the Wheel in a Surface Grinding Process," Manf. Sci. and Engr., ASME Bound Volume – MED Vol. 2-1/MH Vol. 3-1, November 1995, pp. 363-375. [PDF]
181. Melkote, S. N., J. W. Sutherland, and A. R. Thangaraj, "End Milled Surface Texture: The Effect of Tool Flexibility on Back-Cutting," Concurrent Product and Process Engineering, ASME Bound Volume - MED Vol. 1/DE Vol. 85, November 1995, pp. 201-211. [PDF]
182. Sturos, T. J., J. W. Sutherland, K. S. Moon, D. Liu, and A. R. Kashani, "Application of an Actively Controlled Magnetostrictive Actuator for Vibration Abatement in the Turning Process," Proc. of Dynamic Systems and Control Division, ASME Bound Volume - DSC Vol. 1, November 1995, pp. 539-544. [PDF]
183. Wentland, C., W. W. Olson, and J. W. Sutherland, "An Environmental Advisory System for Concept Design: Creation of a Reprocessability Index System," Engr. Data Mgmt. and Emerging Technologies, ASME Bound Volume - CED Vol. 7, November 1995, pp. 67-73. [PDF]
184. Whitmer, C. I., W. W. Olson, and J. W. Sutherland, "Methodology for Including Environmental Concerns in Concurrent Engineering," Proc. of the 1st World Conf. on Integrated Design and Process Technology, Vol. 1, 1995, pp. 8-13. [PDF]
185. Cozzens, D. A., W. W. Olson, and J. W. Sutherland, "An Investigation into the Cutting Fluid Effects on Temperatures in Aluminum Boring," Proceedings of the First Annual International Machining and Grinding Conference, September 1995, pp. 881-891, also appeared as SME Technical Paper No. MR95-210, 1995. [PDF]
186. Domala, K. V., E. J. Salisbury, K. S. Moon, and J. W. Sutherland, "A Study of the Three-Dimensional Structure of a Ground Surface," Proceedings of the First Annual International Machining and Grinding Conference, September 1995, pp. 847-863. [PDF]
187. Haan, D. M., W. W. Olson, and J. W. Sutherland, "The Mechanisms of Metal Cutting Fluids in Machining Aluminum Alloys," Proc. of the Symposium on Assessment and Control of the Industrial Metalworking Environment, November 1995, pp. 301-306. [PDF]
1994
188. Moon, K. S. and J. W. Sutherland, "The Origin and Interpretation of Spatial Frequencies in a Turned Surface Profile," J. of Engineering for Industry, Trans. ASME, Vol. 116, No. 3, August 1994, pp. 340‑347, also in Contact Problems and Surface Interaction in Manufacturing and Tribological Systems, ASME Bound Volume - PED Vol. 67, December 1993, pp. 343-351. [PDF]
189. Vadrevu, S., K. Philipps, J. W. Sutherland, and W. W. Olson, "Loss Function Modeling of Time Varying Quality Characteristics," Trans. of NAMRI/SME, Vol. 22, May 1994, pp. 343‑349. [PDF]
190. Runola, J. P., K. S. Moon, and J. W. Sutherland, "The Effect of Tool Wear on the Wavelength Structure of a Turned Surface Profile," Trans. of NAMRI/SME, Vol. 22, May 1994, pp. 105-109. [PDF]
191. Olson, W. W., and J. W. Sutherland, "Environmentally Conscious Manufacturing," Proceedings of the Japan-USA Symposium on Flexible Automation, July 1994, pp. 1035-1042. [PDF]
192. Makhecha, A., A. R. Thangaraj, and J. W. Sutherland, "Prediction of Drilling Thrust and Torque Using a Mechanistic Model Calibrated Through Non-Linear Optimization," Manf. Sci. and Engr., ASME Bound Volume - PED Vol. 68-1, December 1994, pp. 237-244. [PDF]
193.
194. Vadrevu, S., J. W. Sutherland, and W. W. Olson, "A Value Model for Use in Environmentally Conscious Design and Manufacturing," Manf. Sci. and Engr., ASME Bound Volume - PED Vol. 68-1, December 1994, pp. 93-102. [PDF]
195.
196. Philipps, K., Vadrevu, S., W. W. Olson, and J. W. Sutherland "Concurrent Engineering and the Environment," Proc. of the S. M. Wu Symposium on Manufacturing Science, May 1994, pp. 349-354. [PDF]
197. Vadrevu, S., E. J. Salisbury, K. S. Moon, and J. W. Sutherland, "Modeling of Surface Generation Mechanisms in Turning," Proc. of Mid-America Conference on Intelligent Systems, 1994, pp. 114-121. [PDF]
1993
198. Michler, J. R., K. S. Moon, J. W. Sutherland, and A. R. Kashani, "Development of a Cutting Tool Micropositioner," Trans. of NAMRI/SME, Vol. 21, May 1993, pp. 421-427. [PDF]
199. Kashani, A. R., J. W. Sutherland, K. S. Moon, and J. R. Michler, "A Robust Control Scheme for Improved Machined Surface Texture," Trans. of NAMRI/SME, Vol. 21, May 1993, pp. 429-434. [PDF]
200. Olson, W. W. and J. W. Sutherland, "Research Issues in Demanufacturing," Trans. of NAMRI/SME, Vol. 21, May 1993, pp. 443-450. [PDF]
201. Beard, J. E., and J. W. Sutherland, "Robust Suspension System Design," Advances in Design Automation, ASME Bound Volume - DE Vol. 65-1, September 1993, pp. 387-395. [PDF]
202. Sutherland, J. W., and W. W. Olson, "Tools and Methods for Simultaneous Engineering," Proceedings of the ASM Conference on a Systems Approach to Machining, May 1993, pp. 179-184. [PDF]
203. Sutherland, J. W., "The Role of Computer-Based Simulation in Manufacturing Laboratories," ASEE Annual Conference Proceedings, June 1993, pp. 120-122. [PDF]
1992
204. DeVor, R. E., T. H. Chang, and J. W. Sutherland, Statistical Quality Design and Control: Contemporary Concepts and Methods, Macmillan, 1992, 809 pages. [PDF]
205. DeVor, R. E., T. H. Chang, and J. W. Sutherland, Solutions Manual - Statistical Quality Design and Control: Contemporary Concepts and Methods, Macmillan, 1992, 566 pages.
206. Sutherland, J. W., and K. S. Moon, "Procrustes Analysis and its Application to Sensor Integration," Trans. of NAMRI/SME, Vol. 20, May 1992, pp. 347-354. [PDF]
207. Sutherland, J. W., and W. J. Zdeblick, "Modeling the Thread Chasing Process for Improved Product Quality," Soc. of Automotive Engrs. Technical Paper No. 920919, also in the SAE Trans., J. of Materials and Manufacturing, Vol. 101, No. 5, 1992, pp. 711-719. [PDF]
208. Mistry, A. H., S. J. Schmidt, S. R. Eckhoff, and J. W. Sutherland, "Alkali Extraction of Starch from Corn Flour," Starch/Stärke, Vol. 44, 1992, pp. 284-288. [PDF]
209. Moon, K. S., and J. W. Sutherland, "Improved Image Information Via Procrustes Analysis," Quality Assurance Through Integration of Manufacturing Processes and Systems, ASME Bound Volume - PED Vol. 56, November 1992, pp. 139-150. [PDF]
Pre-1991
210. Oreskovich, D. C., B. P. Klein, and J. W. Sutherland, "Procrustes Analysis and its Applications to Free- Choice and Other Sensory Profiling," Chapter 13 in Sensory Science Theory and Applications in Foods, Eds. H. T. Lawless and B. P. Klein, Marcel Dekker, 1991, pp. 353-393. [PDF]
211. Lin, S. C., R. E. DeVor, S. G. Kapoor, and J. W. Sutherland, "A New Approach to Estimating Cutting Process Damping Under Working Conditions," Trans. of NAMRI/SME, Vol. 18, May 1990, pp. 154-160. [PDF]
212. Endres, W. J., J. W. Sutherland, and R. E. DeVor, "Quality Design Using a Computer-Based Dynamic Force Model for the Turning Process," Proc. 6th Int. Conf. on Comp.-Aid. Prod. Engr., November 1990, pp. 29-42. [PDF]
213. Endres, W. J., J. W. Sutherland, R. E. DeVor, and S. G. Kapoor, "A Dynamic Model of the Cutting Force System in the Turning Process," Monitoring and Control of Manufacturing Processes, ASME Bound Volume - PED Vol. 44, December 1990, pp. 193-212. [PDF]
214. O’Brien, D. J., J. W. Sutherland, and S. G. Kapoor, "A Force-Based Approach to On-Line Flute Breakage Detection in a Peripheral End Milling Process," Automation of Manufacturing Processes, ASME Bound Volume - DSC Vol. 22, December 1990, pp. 47-58. [PDF]
215. Sutherland, J. W., D. J. O’Brien, and M. S. Wagner, "An Algorithm for the Detection of Flute Breakage in a Peripheral End Milling Process," Trans. of NAMRI/SME, Vol. 17, May 1989, pp. 144-151. [PDF]
216. Sutherland, J. W., R. G. Hunter, and R. E. DeVor, "A Quality-Engineering-Based Approach to the Simultaneous Engineering of Products and their Manufacturing Processes," Proc. 5th Int. Conf. on Comp.- Aid. Prod. Engr., November 1989, pp. 1-12. [PDF]
217. Hunter, R. G., J. W. Sutherland, and R. E. DeVor, "A Methodology for Robust Design Using Models for the Mean, Variance, and Loss," Quality Improvement Techniques for Manufacturing, Products, and Services, ASME Bound Volume - PED Vol. 42, December 1989, pp. 25-42. [PDF]
218. Sutherland, J. W., R. E. DeVor, S. G. Kapoor, and P. M. Ferreira, "Machining Process Models for Product and Process Design," Soc. of Automotive Engrs. Technical Paper No. 880793, also in SAE Trans., Vol. 97, No. 5, 1988, pp. 215-226. [PDF]
219. Sutherland, J. W., P. M. Ferreira, R. E. DeVor, and S. G. Kapoor, "An Integrated Approach to Machine Tool System Analysis, Design, and Control," Proc. 3rd Int. Conf. on Comp.-Aid. Prod. Engr., June 1988, pp. 429- 445. [PDF]
220. Sutherland, J. W., "A Dynamic Model of the Cutting Force System in the End Milling Process," Sensors and Controls for Manufacturing, ASME Bound Volume - PED Vol. 33, November 1988, pp. 53-62. [PDF]
221. Sutherland, J. W., and T. S. Babin, "The Geometry of Surface Generated by the Bottom of an End Mill," Proc. 16th North Am. Manf. Res. Conf., May 1988, pp. 202-208. [PDF]
222. Sutherland, J. W., G. Subramani, M. J. Kuhl, R. E. DeVor, and S. G. Kapoor, "An Investigation into the Effect of Tool and Cut Geometry on Cutting Force System Prediction Models," Proc. 16th North Am. Manf. Res. Conf., May 1988, pp. 264-272. [PDF]
223. Richardson, S. J., M. P. Steinberg, R. E. DeVor, and J. W. Sutherland, "Characterization of the Oxygen-17 Nuclear Magnetic Resonance Water Mobility Response Surface," J. of Food Science, Vol. 52, No. 1, 1987, pp. 189-193. [PDF]
224. Babin, T. S., J. W. Sutherland, and S. G. Kapoor, "On the Geometry of End Milled Surfaces," Proc. 14th North Am. Manf. Res. Conf., May 1986, pp. 168-176. [PDF]
225. Sutherland, J. W., and R. E. DeVor, "Error Prediction in Flexible End Milling Systems," J. of Engineering for Industry, Trans. ASME, Vol. 108, No. 4, November 1986, pp. 269-279.
226. Babin, T. S., J. M. Lee, J. W. Sutherland, and S. G. Kapoor, "A Model for End Milled Surface Topography," Proc. 13th North Am. Manf. Res. Conf., May 1985, pp. 362-368. [PDF]
227. DeVor, R. E., J. W. Sutherland, and W. A. Kline, "Control of Surface Error in End Milling," Proc. 11th North Am. Manf. Res. Conf., May 1983, pp. 356-363. [PDF]
228. Miller, J. C., J. W. Sutherland, and R. E. DeVor, "Surface Roughness Characteristics for Turning 380 and 390 Aluminum Casting Alloys," Proc. 10th North Am. Manf. Res. Conf., May 1982, pp. 282-288. [PDF]